How to Clean a Table Saw Blade

Regardless of the saw blade, you use in your wood projects. Either a miter saw, circular saw or a table saw. Dirt is something that falls in the way after using them for a bit longer, thus cleaning blades is essential.

Point to be highlighted here, and many woodworkers don’t recommend washing blades with watery liquids. By the reason they can produce rust on edges, that is for sure, any woodworker never will want to let this happen. But there’s more to this, water is usually the best way to clean up a blade, and with the mixture of different kinds of cleaners, it is as effective as products found in the markets.

Nonetheless, make sure you dry every single droplet of water from the blade. And to do this, place the edge in the sunlight for some time. People living in areas shortage of sun can use hair dryers to soak up moisture from the blade.

The primary cause of a lowered cutting performance is a dirty table saw blade. Clogged with grease and rust built up over a knife can crop up many problems. For instance, rough edges, power loss, and, primarily, woods get burn marks on them.

So if you’re looking for the best possible way to clean a table saw blade. Here’s what we’ll be covering in this article.

Steps to clean, clean a table saw blade.

Clean the blade of a table saw by following this simple process below. Everything you need to follow is probably is found in your home—no need to put money on this.

The following things are needed:

  • Warm Water (avoid cold water)
  • Cleaning agent, detergent, baking soda, acetone, or any cleaner you have, you can use.
  • Brush, Either has Nylon bristle or soft wire-bristle. Both will do the job.
  • Aluminum or plastic pan.
  • Fabric cloth

Remove the blade first

A dirty table saw blade can only be appropriately cleaned once you remove it. Without it, you may not get the most out of it, even if you think you’ve cleaned it very well.

Therefore, if you wish to remove it, be sure to cut off its power supply. Now pick a screw and loosen the nuts. Be self-prepared and avoid touching the blade’s teeth that may hurt you real bad.

Lay the blade on a pot filled with warm water

Take a pot larger than the blade size of your table saw. The pot’s bottom should be flat so that the blade rests evenly upon it. Fill it with warm water, make sure the edge. Itcaution is completely swallowed.

If you’re using a steel-made pan, it’s better to place a rag before thawing the blade inside it. This will prevent the blade’s teeth from being damaged by the friction made of the pan surface.

Mix cleaner in the water

A wide range of cleaning products can be used to clean table saw blades. It is possible to utilize detergent, hydrogen peroxide, and cleaners that are commonly found in grocery stores. Baking soda, in addition, is not far behind.

Superior to all options mentioned above, there are different brands manufacturing cleaners, especially to clean up such blades. If you use them, don’t forget to wear gloves since they are more effective and aid in wiping out stubborn dirt such as glued-greasse.

Once you have dissolved the cleaning agents in the water, rest the blade for 10 minutes in the pot. The time you need may vary depending on the product you use. Look at the dirt on the blade, it should wash off.

Brush it

In the above step, it’s for sure not all the dirt will wash off. You may need to brush manually to clean up each tooth blade. While doing this, take enough cautions as holding blades on hands could be dangerous.

You can use any nylon toothbrush to do this job. For severe blade conditions, you can use a steel bristle brush instead.

Let the blade completely dry.

After the cleaning process, to prevent rust from developing. Make sure you dry the blade wholly since the water droplets can cause it to formgrease

So to prevent rust from forming up and maintain the blade, use a fabric rag and rub it over the blade until it soaked up all the water. And keep the blade in the sunlight for further dryness.

Nevertheless, if you live in a humid environment where sunlight is hard to see. Use a hairdryer to soak up moisture instead.

Spray Some Dry Lubricant

Before attaching the blade back into the table saw. You should use some kind of Dry lubricants that are manufactured for keeping the blade’s condition maintained for longer. And additionally, coat to prevent rust clogging.

You can purchase this product from any generic grocery store at a low cost. Applying it is also very simple, you can consult with the salesman.

However, most of them are like sprayers, so throw the liquid on the blade and mop the surface with a dry cloth. Once it gets dried, now you can place the blade where it belongs.

You can read it also : Cutting a 45 Degree Angle with a Table Saw

FAQs

Does vinegar clean saw blades?

Yes, Vinegar can also do the trick in cleaning a table saw blade. Remove the blades off from the table, and put some vinegar liquid onto each tooth. Wait for almost 20,30 minutes until the vinegar reacts with the grease and pull it off. Now, take a dry fabric, and clean if any moisturizer is left.

Can you use acetone to clean saw blades?

Partially yes, but acetone may not be a great choice to clean up a blade. For the fact, it can damage and blade sharpness, using it multiple times can decrease the blade’s cutting capacity. In the end, the blades may not be able to deliver smooth cuts, resulting in you having to buy a replacement. Therefore, it’s partially not recommended. Rest assured on your choice, that’s said you can use once or twice but not regularly.

How do you keep a saw blade from rusting?

In order to maintain a blade’s sharpness in efforts to make it last longer, and protect it from being resting. Always clean them after using blades for a bit longer. You should have a dusting cloth on your table to pull off wood dust that often rests on the blades.

Still, it’s not just enough because tiny particles don’t get off in this way. So, if you see some dirt is clogging up, make you mind cleaning it water or cleaner if you have.

Most importantly, don’t let moisture rest over the blades. Often people cover them with a piece of cloth to protect blades from dust. But, this causes moisture to be formed due to air blockage.

Finally, there are some lubricants to be found that are particularly designed to put over raw machinery to block rust to develop. You should have that in your workplace.

Leave a Comment