How to plane wood without a planer

So you’re looking for alternative ways to plan a piece without a planner. It can be challenging to do this job, still, alternatives we’ll be listed here will probably do the trick.

Regardless of whether you have a wide piece of wood or a small-sized one, you will achieve the results you need in the end.

Following are the ways to plan or smoothly flat a wood piece without a panner

Use a sandpaper

The best way out there you can go is to use sandpaper. An old fashioned-way that will take you a long amount of time and effort, but certainly you will get the results you want. It’s also a way to go for people having no power tools and needing a budget-friendly substitute to persist.

There are options to be found in the sandpaper. Anyhow among the best choices is the “coarsest sandpaper” it’s basically made of wood, and when wrapping over a block of wood it grips comparatively solidly on hands. That makes it produce a smoother finish. Still, you can go with the sanding paper as long as you feel comfortable with it.

It would be nice for you to take some advice here: Always wear a mask before starting to work with sandpaper. In case of working with a bigger woodblock make sure it’s level-fixed on the ground. This will help you rub the sandpaper forcefully- Don’t put too much force instead keep it balanced.

Read it also : How to Clean a Table Saw Blade

Using a table saw

If you’re into woodworking by passion or by profession. You might own a table saw for sure. If you’ve one, then you can use it to plan a large block of wood. It’s a little technical and required some expertise to get a smooth and flatten end-result.

To begin with, first check the surface of the table saw, it should be completely flat otherwise you will end up with a curve on the board.

Now set the blade at 90 degrees. To confirm the blade angle if, on the right settings, you can use a device that is attached to the blade, and shows the degrees in number when tilting the blade. Accuracy is the first thing to look for.

Now after setting up the basic things, it’s time to place the wood board that needs to be flattened on the table saw.

Push it onto the parallel direction of the blade while contacting it’s one side with the rotating blade so it gets cut with every inch push.

One thing to pay attention to here, you while doing this. Don’t stop pushing in the middle because the wood might get burned by the rubbing.

Use a jack plane

Assuming that you don’t own any power tool, neither you prefer using sandpaper for the fact it takes too long to flatten a big piece of wood. Under these circumstances, the one substitute you can have is a jack plane.

Jack planes work the same as the planner, but they don’t have a motor installed in them. You will have to put manually force to get a job done.

To begin working with this apparatus, there are some things to bear in mind. Such that, you will need to make sure the surface is equally balanced where you place the wood piece.

For the reason that you can level wood equally from all over the surface.

Moreover, there are different sizes to be found of this tool, depending on the wood you can choose them. About sizing, that said, a 4,5 number words efficiently against the wood size of 5,6 inches. However, the longer the board size goes, you will better have a bigger jack planner, to have a conformable experience working with your project.

Use a router

A router can also be a substitute for a wood planer if you have this at your workplace. But it might not give a smooth finish unless you do some practice over a rough board to set your hands and the force to put on it.

Another reason it might not be the best bet is that it requires equal forced to furnish a wood, which is a big problem for beginners, therefore, they often make wrong cuts and gets edges on the wood instead of making it flat.

You will aboard, it’s like assistance for woodworkers that securely hold a place within a wooden frame, generally made for a firm grip on the wood.

The working application of a router when you use it as a wood planer is similar to using a table saw. But unlike the table saw, where you push wood against the blade, you will have to rib this router above the wood, touching the uppermost surface, and balancing every inch should be given high priority.

Leave a Comment